دانلود کتاب Surface Modification Technologies XIII - Proceedings of the Thirteenth International Conference Held in Singapore

The Thirteenth International Conference on Surface Modification Technologies was hosted by "Nanyang Technological University" and held jointly with the "Processing and Fabrication of Advanced Materials" conference at Singapore, between September 7-10, 1999. This meeting was the smallest SMT meeting ever in its 13 years with numerous papers from Singapore and the Asian countries and very little representation from the major countries. Over 18 countries were represented at this meeting and this proceedings is a compilation of the 46 papers that were presented. The meeting was co-sponsored by the American Society for Materials (ASM International), Institute of Materials (10M) and several other materials societies. The papers presented in these proceedings cover a broad spectrum of topics and represent the diverse nature of the field. All the papers included in these proceedings were peer reviewed and corrected prior to publication. Content: Front Matter • Table of Contents •Part I. Hard Materials 1. Surface Oxidation of Steels at Low Oxygen Pressures and Elevated Temperatures, and its Impact on Gas Nitriding 2. Effect of Ar Ion Bombardment on the Surface Layer of Ion Nitrided Cr-Mo Low Carbon Steel 3. Influence of Sputtering Parameters on Residual Stress of CoCrTaPt Magnetic Thin Film Coating 4. Analysis of Structure and Properties of Diamond Like Carbon Films by Ion Beam Deposition 5. Microscopic Observation of Corrosion of Amorphous Carbon Coated Magnetic Recording Disks with CrN Interlayer 6. Diamond Coating on WC-Co Tools 7. Growth of SiCN Films by Magnetron Sputtering 8. Formation of β-C3N4 Grains by Sputtering 9. Potential of Duplex Treatment: Combining Plasma Nitriding with Carbon Nitride Films 10. The Influence of FEP Additions on the Properties of WC-Co Coatings Obtained by Detonation Spray Coating 11. Nucleation and Growth of Polycrystalline Diamond Particles on Ceramic Substrates by Microwave Plasma CVD •Part II. Lasers/Surface Melting 12. Sintering Behavior of Nano-Ceramic Coatings 13. Laser Surface Hardening of Steel by Low Power CO2 Laser •Part III. Electrodeposition and Evaluation of Modified Surfaces 14. An Instrument for Measuring Instantaneous Value of Internal Stress of Electrodeposit 15. The Effect of Pad Dimension on Growth of Flip Chip Electroless Nickel/Electroplated Solder Bump 16. Crater Wear Mechanisms of TiN Coated High Speed Steel Tools 17. Parametric Impact on the Microstructure and Wear Behavior of Laser Surface Alloyed Iron Boride Layers 18. Evaluation of the Abradable Performance of Clearance Control Coatings 19. Rapid Tools with High Quality Surface Finish and Strength Using High-Temperature Epoxy Resin and Electroless Nickel Plating •Part IV. Thermal Spray Techniques 20. Morphology of Oxide in Thermal Sprayed Metal Coatings 21. Thermal Shock Testing of Plasma Sprayed Discs 22. The Effect of Top Coat Sintering on Ceramic Spallation in Plasma-Sprayed Thermal Barrier Coatings 23. Comparison of Computer Modeling and Measurements in Plasma Spraying of Ni and Al2O3 24. A Process Control Methodology for D.C. Plasma Spraying 25. A Comparative Study of the Performance of Two Diverse Detonation Spray Systems •Part V. Nitride Coatings 26. Surface Oxidation of Aluminum Nitride Thin Films 27. Deposition of AIN Films by RF Reactive Magnetron Sputtering: Effect of Processing Parameters •Part VI. Evaluation of Modified Surfaces 28. Characterization of Gas and Liquid Nitrocarburizing Microstructure and its Influence on Wear and Mechanical Properties 29. Microstructure and Mechanical Properties of PVD WC/C Coatings 30. Characterization of Sol-Gel Derived PZT Films Prepared at Low Temperatures 31. The Stability of Aluminide Coatings on Ni-Based Superalloy In-738 in Electrochemical Hot Corrosion Test 32. Transparent Conducting Coatings: Applications, Materials, and Deposition Techniques 33. Calculation of the Adhesive Strength by Using the Fracture Mechanical Test Methods 34. Influence of the Pulse Duration on the Application of Laser Shock Technique for the Debonding of Coating 35. Gelling-Induced Autophobicity Effects in Multi Layered Sol-Gel Coating Systems •Part VII. Posters 36. Adhesive Wear Resistance of HVOF Sprayed Cu Based Alloy Coating 37. Preparation of Fluorinated Amorphous Carbon Nitride Films by Magnetron Sputtering 38. Acoustic Emission Evaluation of Plasma Sprayed Functionally Graded Thermal Barrier Coatings 39. Wear and Friction of Diamond Coatings Deposited on Pure Titanium 40. Improvement of Interfacial Structure of Diamond Coating on Ti by Duplex Surface Engineering 41. Wear Resistance of Three Chromium-Based Coated JIS SKD61 Tool Steels 42. Effect of Surface Modification on Room Temperature Tensile Properties of Fe-18AI and Fe-18AI-5Cr Alloys 43. Reactive Plasma Spray of Nickel Aluminide Coatings from Elemental Ni and AI Powders 44. Surface Microstructure Effects of Single Crystal Tungsten after Nd:YAG Laser Irradiation 45. Surface Modification of PTFE by Plasma Treatment 46. Effects of an Additive on the Corrosion Performance of Electroplated Zinc on Different Alloy Steels Subject Index Author Index